Sol by Scan Dimension

Error Codes and Messages

Error Code

Message

0x1000:01

Turntable rotates inaccurately. Scanning will stop. Check cables and weight of object.

0x1000:02

Camera operates with a suspiciously low FPS. Scanning will stop. Check cables.

0x1000:03

Turntable rotation angle after rotations is same. Check cables and weight of object

0x1100:01

Impossible to set the sharpness to value: %1.

0x1100:02

Impossible to disable video compression. Has the latest Realtek firmware been downloaded? Program will continue with video compression.

0x1100:03

Feature not yet implemented.

0x1100:04

Currently stored serial number does not have the correct format! Check camera and mainboard!

0x1100:05

Serial number does not have the correct format. Serial number will not be written to the device.

0x1100:06

Serial number has already been used before on sftp-site.

Serial number will not be written to the device, calibration will fail.

0x1100:07

Error while writing serial number to the device

0x1100:08

Serial number %1 has been written to the connected device. Be careful not to use this serial number again for other devices!

0x1100:09

Serial number %1 has already been written to the connected device.

Be careful not to use this serial number again for other devices!

0x1100:10

Serial number does not have the correct format

0x1100:11

Error starting or connecting to UR-robot

0x1100:12

Error uploading to sftp-site. File missing

0x1100:13

Error downloading from sftp-site

0x1100:14

Error uploading to sftp-site

0x1100:15

Error making connection to sftp-site

0x1100:16

Serial number has been used before.

0x1100:17

File could not be saved to excel

0x1100:18

Calibration data file could not be read

0x1100:19

Robot would go outside its bounding box. No move performed

0x1100:20

Laser could not move to requested angle

0x1100:21

Angular offset is not yet determined. Leave calibration anyway?

0x1100:22

Laser is not yet %1 adjusted correctly. Leave calibration anyway?

0x1100:23

Camera is not yet %1 adjusted correctly. Leave calibration anyway?

0x1100:24

Turn the laser screw %1 minutes clockwise

0x1100:25

Turn the laser screw %1 minutes counter clockwise

0x1100:26

Turn the camera screw %1 minute(s) clockwise

0x1100:27

Turn the camera screw %1-minute(s) counter clockwise

0x1100:28

Turntable test has failed

0x1100:29

Folder %1 can't be created. Stopping application.

0x1100:30

Z-axis calibration has failed

0x1100:31

Scanner %1 adjustment has failed

0x1100:32

Focus calibration has failed

0x1100:33

Camera calibration has failed

0x1100:34

Laser camera calibration has failed

0x1100:35

Not enough laser measurements.

Is the laser moving the way it should?

0x1100:36

Too high laser movement reside. Is the laser moving the way it should?

0x1100:37

Laser range is not okay. Does the magnet have the right North-South orientation? Or is the laser cable stuck and can't move freely?

0x1100:38

Looks like there is no magnet mounted.

0x1100:39

The test has failed. Do you want to retry?

0x1100:40

The programmer never expected to come to this point in code

0x1100:41

The %1 drive does not exist ... aborting !!!

0x1100:42

Serial number %1 has been registered successfully.

Be careful not to use this serial number again for other devices!

0x1100:43

Could not read camera serial number. Bad connection between main board and camera?

0x1100:44

XML data is corrupted and can't be read

0x1200:01

There is an issue with the internet connection. Please check your settings and try again. 

0x1200:02

Aborting, this scanner has been declared defect and can therefore no longer can be used.

0x1200:03

Aborting, cannot find calibration file.

0x1200:04

Correct settings for this distance are not found in xml file.

0x2000:01

Obj file is corrupted. Cannot proceed with upload.

0x2000:02

Network error occurred. Cannot proceed with upload.

0x3000:01

Cannot load requested file

0x3000:01

Camera connection was lost.

Reconnect your cables and restart dialog.

0x3000:02

For given parameters a mesh cannot be constructed.

0x3000:03

Cannot find raw points to be exported.

0x3000:04

There is no mesh to process.

0x3000:05

There is no fused mesh to work with.

0x3000:06

Cannot start since no PCL was found.

0x3000:07

Impossible to set the exposure to value: %1

0x4000:01

Cannot access USB camera device, application is quitting now.

Reconnect USB cables and start application again.

0x4000:02

Cannot access USB turn table, application is quitting now. Reconnect USB cables and start application again.

0x4000:03

The turntable doesn't rotate correctly. Connect to another USB super speed port and restart application.

0x5000:01

Free up some space on your hard disk before starting a new scan.

0x5000:02

Cannot start new scan.

0x5000:03

The scene is empty, there is nothing to reconstruct. Did you place object on turn table

0x5000:04

Impossible to set the focus to value: %1

0x5000:05

Since the automatic alignment of the last scan to the model has failed

We are proceeding directly to the meshing stage.

0x5000:06

Automatic distance determination has failed. Did you remove the object?

0x5000:07

Point clouds are empty. Cannot proceed.

0x5000:08

Turn table markers are not found.

Cannot proceed.

0x6000:01

Email is not valid.

0x7000:01

Could not register, we will try next time program runs

0x8000:01

Cannot find surface to be exported.

0x8000:02

Cannot find optima points to be exported.

0x9000:01

There are no raw points.

0xA000:01

Cannot construct proper camera matrix. Texturing might fail.

0xB000:01

Cannot export: there is no fused mesh to work with.

0xC000:01

Your graphic card does not support the render features.

0xD000:01

Another instance of the application is already running.

0xD000:02

Not possible to create data folder.

0xD000:03

Warning: Windows media pack is not installed.

0xD000:04

Warning: The PC does not have a recommended CPU installed.

0xD000:05

Warning: The PC does not have the recommended RAM available.

0xD000:06

Warning: The Hard Drive does not have the recommended free space

0xD000:07

Aborting, calibration file is corrupted.

0xD000:08

MD5 sum does not match. Executable is corrupted!

0xE000:01

Cannot proceed. Perform calibration for the current camera focus first.

0xE000:02

Table markers were not found

0xE000:03

Table markers definition file (Rubi.tpat) was not found.

0xF000:01

There is a mismatch between attached device serial number and xml serial number. Stopping.